Getting Familiar with Plumbing: The First Step for Bathtub Installation
Getting Familiar with Plumbing: The First Step for Bathtub Installation
Blog Article
What are your ideas regarding A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old bath tub with a new one is likewise a moderately difficult job. If the old tub is easily obtainable, the project can relocate rapidly; if you have to open up a wall to remove the old bathtub and place the new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to vacate the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the task and also fit trying it. Rather than employing a contractor to take control of a halfway-completed task, it is better to think about using one prior to you start. Chances are you may need an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't need to change the plan of your previous supply of water pipelines.
Your tools and also product checklist need to make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Safeguard the tap in position with the producer offered backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former type needs to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using the two wood boards under its feet, put the bathtub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the tub up until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water system and examine all joints and also new pipework for leaks and also tighten them if required. Fill the tub as well as likewise examine the overflow electrical outlet and also the normal outlet for leakages.
Lastly, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub must wait up until the bathtub has been used at least when as this will certainly settle it into its final position.
Planning for the Setup
Firstly, the sustaining frame provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets unit to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bath and also the tiling, leading to problems with wetness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and also cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly very early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very curious about A Step-by-Step Guide to Installing a Bathtub and I am praying you enjoyed the new blog entry. Sharing is good. Helping others is fun. Thanks a lot for your time spent reading it.
Click Here To Read More Report this page